CamCraft

Reference

Glossary

Each entry says how CamCraft uses the term and links to the guide page that covers it in depth. Terms are listed alphabetically.

Adaptive. A Milling 2D operation kind that roughs an area in adaptive passes, and also one of the 3D Pocket strategies. See Operations.

Capabilities. The mask a .cps post declares in its manifest: 1 for milling and 2 for turning. A post that declares no mask is read as not turning, so CamCraft never guesses what a dialect speaks. See Posting.

Carried stock. The material a setup leaves behind. A later setup can take it as its stock source instead of the raw stock, so verification and rest machining see the material already removed. New setups can also carry stock and the work offset over from the active setup. See Setups.

Collision. A move that strikes a fixture. The post checks the whole program for collisions and refuses to write it when a move hits one. See Posting.

Dialect. The controller's own flavour of G-code, which a post script writes. The Post page offers the dialects by name. See Posting.

Generate. Computes an operation's toolpath and checks it. A generate that cannot make a safe path stops with a message that names the setting or geometry at fault, and never leaves a partial path. See Operations.

Gouge. Material removed from the part where the program cuts into the model. The post refuses a program with a gouge, and Deviate shows where it is. See Reading a refusal.

Holder. The tool holder that clamps the cutter. A holder profile is drawn in the tool editor or taken from the holder library, and a holder that hits the part is flagged as a warning on the operation. The guide has details in Tools and tool libraries.

Holder body. The holder's body, the section above its nose that the tool editor's Body tab draws. It is checked against the part like the rest of the holder. See Tools and tool libraries.

Live tooling. A driven tool in a lathe or mill-turn turret. When a path states spindle C angles it is live-tool work: the S word drives the live tool, and the work turns only on C. See Setups.

MCP. The Model Context Protocol. camcraft-cli mcp serves CamCraft as an MCP server, so an AI agent can drive it headlessly through the same undoable commands the window uses. See Posting.

Mill-turn. A machine that mills and turns in one setup. Mill-turning on the Setup group shows both the milling and the turning operation groups. See Setups.

Model. An imported 3D mesh or STEP file (STL, OBJ or STEP) that describes the part. Import it with Model on the File group. See First run.

Operation. One machining step: a tool, an area to cut, and how to cut it, set on its Geometry, Heights, Passes, Lead in / Lead out, Feeds and (on a few kinds) Machine tabs. See Operations.

Part. The physical piece being machined. The models describe it, the stock is cut into it, and Deviate compares the machined stock with it. See First run.

Post. A post processor: a .cps script that turns the operations into one controller's NC program. A setup picks its post on the Post page, or loads its own with Load post (.cps). See Posting.

Reduced fidelity. A STEP model imported with a coarser mesh than the importer promises. The model page flags it, and the program gate refuses to post on verdicts it cannot honour until the model is imported again at a higher step budget. See First run.

Refusal. CamCraft declining an action it cannot make safe. A refused post, change or generation writes nothing and names its reason; it is not a crash. See Reading a refusal.

Rest material. The material still uncut after the earlier operations, which later operations and rest machining work from. Frame rest takes the view to the worst uncut spot. See Operations.

Setup. One way the part is held on one machine: its stock, work offset, machine, post, fixtures, tools and operations. See Setups.

Setup sheet. A text page for one setup listing its tools in change order, with cut and rapid lengths and the estimated time. Export setup sheets… writes them; posting does not. See Setups.

Stale. An operation whose toolpath no longer matches its inputs: the model, stock, tool, work offset or its own settings changed after it was generated. A stale operation blocks posting until it is generated again. See Operations.

Stepdown. The depth of cut per pass along the tool axis, a setting on the Passes tab. See Operations.

Stepover. The sideways distance between adjacent passes, a setting on the Passes tab. Auto applies the scallop law where the kind offers it. See Operations.

Stick-out. The length from the tool tip to the holder's nose face: the flute plus the shank, shown on the tool's holder profile. See Tools and tool libraries.

Stock. The raw block the part is cut from: a box, a cylinder or a copy of a model, set with Stock on the Setup group. Verify and simulation cut into it. See Setups.

Stock to leave. Material left on the part for a later operation to remove, set as Stock to leave on the Passes tab. See Operations.

Tool spindle. The spindle that turns the cutter, as opposed to the work spindle that holds the chuck. A milling post's S drives it. See Setups.

Toolpath. The cutter moves an operation generates and caches on the operation. Paths shows every cached toolpath at once. See Operations.

Verify. The check on the whole program before it is written: the simulated stock has no gouge, no move strikes a fixture, and no move exceeds a limit the mounted machine states. See Posting.

WCS. The work coordinate system the program is written in. Each setup owns one, and the post labels it G54 to G59. See Setups.

Work offset. The placement of the WCS on the stock, set with Origin on the Setup group. Heights measured from the work offset read the setup's offset. See Setups.

Work spindle. The spindle that holds the chuck on a lathe or mill-turn. A turning section opens on it, and a constant-rpm (G97) speed over the setup's chuck rating is refused rather than capped. See Setups.