Multi-axis
Multi-axis machining adds rotary axes to the three linear ones. This section
covers the four kinds of multi-axis work, what CamCraft does for each, what
you set up, and what it checks before a program posts. It describes the
program on main and says plainly where a feature does not exist yet.
| Kind | The rotary axes | What CamCraft calls it | Page |
|---|---|---|---|
| 4-axis indexed (3+1) | One rotary turns to a fixed angle, then 3-axis cutting | A tilted plane (3+2) with the A angle only | Indexed work |
| 5-axis indexed (3+2) | Two rotaries hold a fixed orientation, then 3-axis cutting | A tilted plane (3+2) with A and B | Indexed work |
| 4-axis continuous | One rotary turns while cutting | Rotary Contour, Rotary Parallel, Rotary Offset | Continuous 4-axis |
| 5-axis simultaneous | All axes move together | 5-Axis Contour, 5-Axis Parallel, Swarf, Advanced Swarf, 5-Axis Flow, Multi-Axis Rough, Multi-Axis Contour | Simultaneous 5-axis |
Read first Machines, kinematics and TCP: which machine file you mount decides what is allowed, and the post you pick decides whether tilted moves post at all. The list of checks says what is refused and what only warns.
Machines that ship with a rotary axis
Of the machine files in assets/machines/, four state a rotary axis. Every
other shipped machine is 3-axis (or a lathe).
| Machine file | Rotary axes | Notes |
|---|---|---|
doosan-dnm.mch (Doosan DNM 5700 + rotary table) | A about X, travel stated as 360000 degrees, no nose_to_axis | A table. Pairs with doosan-dnm.cps. The catalog gives no nose-to-axis figure, so every op refuses until the setup states its own (SetSetupNoseToAxis). The plain 3-axis machine is doosan-dnm-3axis.mch (Doosan DNM 5700). |
tormach-770mx-microarc4.mch (Tormach 770MX + microARC 4) | A about X, -360 to 360 degrees, nose_to_axis 10.6 | A table. Pairs with tormach.cps, which indexes A only. |
tilthead.mch (Tilt-head 5-axis) | A about X and B about Y, each -120 to 120 degrees, carrying the head | Head-head tilt. The 5-axis machine in the set. |
millturn.mch (Multitasking 5-axis) | C about Z, -360 to 360 degrees | Mill-turn; a C axis tilts nothing. |
To add a rotary to your own machine file, follow
docs/MACHINE-ONBOARDING.md:
state the rotary part with its axis direction, its travel in degrees, and
(for a table that turns the work) its nose_to_axis.
Related pages
- A complete indexed job on the Tormach 770MX and the microARC 4, from the model to the posted program, is in Your first 4-axis part.
- The per-operation reference for the multi-axis operations is in Multi-axis operations.
- What each machine type means for setups and operations is in Machine types.
- If a post is refused, see Reading a refusal.
- Machines, kinematics and TCP - Table-table, head-head and tilt-head machines, which axis limits apply, and what each post does with tilted moves.
- Indexed work: 3+1 and 3+2 - Turn the rotary to a fixed angle, then cut with ordinary 3-axis operations.
- Continuous 4-axis: rotary operations - Rotary Contour, Rotary Parallel and Rotary Offset: finishing and roughing a turned shape on a rotary.
- 5-axis simultaneous - Swarf, flow, contour and roughing with the tool axis moving: lead, lag and the tilt limit.
- Checks on multi-axis work - Reach and travel, the tilt tolerance, tool and holder collision, index swing, and what is refused or only warned.
- Multi-axis operations - One section per multi-axis kind: what it is for, its key settings and defaults, what it picks, the reach and collision checks, and the refusals you are most likely to meet.